Auto Motor News

The two main factors affecting the performance of a audio system are volume and the quality of sound that it produces. In a car stereo system, the perfect quality can be achieved only when the stereo system is connected to the amplifier. The most common thought among people is that amplifiers increase the sound alone but they also increase the overall quality of the sound coming from the stereo system. But how to connect an original car stereo to an amp?

There are few tools which are found useful in connecting an original car stereo to an amp. It includes speaker wire, rubber grommets, wiring harness adapter, amplifier wiring kit, drill, Philips head screw driver, trim panel tool, rubber spacers.

A few tools are required to complete the job these make the job easy and faster. It includes speaker wire, rubber grommets, wiring harness adapter, amplifier wiring kit, drill, Philips head screw driver, trim panel tool, rubber spacers.

The first step is to disconnect the wire connected to the negative terminal of the battery. This wire establishes a connection between the battery and the car’s frame. The next thing to do is to remove the clamp and keep it away. This can be done with the help of a Philips head screw drive.

The amplifier is mounted on the trunk of the car. In the case of trucks the amplifier is mounted below the seat to provide ventilation. The vehicle’s stereo is removed. The removal procedure varies from one vehicle to other. The manual which is issued along with the vehicle by the manufacturer is to be referred often. The stereo unit is pulled to the dash till the wiring in the rear.

The cables are drawn to the amplifier location. The panel protecting the carpeting is removed using a panel tool. Now the cables are placed below the carpeting and our hands are used in the place of the panels. The cables used for power supply are drawn starting from the battery up to the amplifier. Then the cables and the leads are connected to amplifier.

The stereo system of the car is removed. The process of removing it varies from one car to another and so it is better to go through the user’s manual before doing this job. Take out the stereo so that the wires in the back side of the stereo can be accessed easily. Now the wires attached to the stereo system are removed. Then the wires are connected to a adapter. This connection is easy to make because all the wires are colour coded.

Technology has made things easy and simple though it is complicated in its own working. The above article would have taught you how to connect an original car stereo to an amp. These works must be done with caution and accuracy. Thus take time to do this simple work with care.

Learn more about Auto. Stop by Author Name’s site where you can find out all about Car stereo and what it can do for you.

If your car still has the cassette player than you feel very annoyed to repeat the track each time where you can to rewind, stop, play in a cassette player its highly recommended that switch over to an-in dash CD player using this tips on how to install an-in dash CD player. The CD player can be installed in the dash board by replacing the cassette player. But one has to ensure that he has an idea of the automobile make and its model so that the installed CD player is fit as in stock model.

Here is the list of the things that you will need for completing the switch over; wire strippers, car stereo wiring connectors, 20 vinyl butt splices that are insulated awg 16-14, needle nose or combination pliers and 1 CD player dash install kit.

First locate for the wire running from the CD player, using a stripper strip the wire to half an inch, The same procedure is to be repeated for all the wires provided with wire connector, make sure only the insulation part is removed without damaging the core portion of the wire.

Insert an end of the orange wire coming out of the wiring connector of the car stereo into the vinyl insulated butt splicer. Now close this side of the splicer. This can be easily done using the nose pliers. Make sure that the butt splicer holds the wire firmly. Now insert the end of the orange wire that is coming out of the rear end of the CD player into the other end of the butt splicer and close this end with the use of the nose pliers. Be sure that there are no loose connections and the wire is held firmly by the butt splicer. Repeat this step for all the wires that can be seen in wire connecting the stereo. Make sure that each wire is matched very well with the similar colour and size of the player.

With the help of your car owner’s manual remove the dash board covers from its place. Now take the new disk player and stereo wiring connector that you have purchased from the market and insert it into the dash install kit. Now connect the automobile’s connector to the car stereo wiring connector. Push the connectors together. You will hear a click when the connection is complete.

Now one of vinyl butt splice which is insulated and the orange wire’s end is inserted from the wiring connector. The connection is done securely using the pliers. The pliers are used to cover the side of vinyl insulated butt splice. Now in a similar way fix another vinyl insulated butt splice from one of the orange wires that comes out from the player. Then using the pliers the vinyl insulated butt splice is securely connected to the wire.

To make sure that all the connections are properly made and the stereo is working properly, turn on the ignition and check. After checking, replace the dash board coverings.

Now the remaining wires that sag are put behind the CD player and arranged so that it gives a clean finish. The CD player is screwed to the dash board, and the set up is checked by turning on the vehicle and the stereo system. If the working is smooth the dash board is replaced to its appropriate location. The tips on HOW TO INSTALL AN-IN DASH CD PLAYER are so lucid that it eliminates the need for supervision.

Find out more about Autozubehoer. Stop by Author Name’s site where you can find out all about Car stereo and what it can do for you.