Auto Motor News

How to Install an Amp Kit? Amplifier wiring is a difficult task. With wiring kits this work can be done much easier. Still some work has to be done for attaching everything and you can go wrong. This wiring kit costs lower than the cost of the individuals.

The first thing to do before starting is the disconnection of the battery of the car. First the negative then the positive terminal is removed. If there is any hole in the heat shield coating in the car then use it. Or else make a small hole that is big enough to fit the power wire and heat protective wire cover.

The things needed to do this job are wire stripper, soldering gun , drill which is optional, a wrench that is adjustable and a screw driver. Keep these things ready before starting the work . Let us look at the steps in detail.

The end of the power wire is hold nearest to the fuse holder which is under the hood. The other end of the power wire is fed into the hole drilled in the heat shield. The wire is fed continuously along the side of the car till the rear seats are reached. The wire is further fed under the rear seats through the small gaps till it reaches the trunk. From the trunk the wire is taken to the positive terminal of the amplifier. End of the wire is stripped and it is connected to the positive terminal of the amplifier.

The bolt present under the carpet is spotted then it is unscrewed and then connected with ground wire. The connection can be made very secure by soldering the two wires. Now the ground wire is connected to the amplifier’s negative terminal. To ensure safe connection between the wires, the screws are tightened well.

In the next step grounding of wire is done. A bolt is located and then tightened to secure the connection tight with the ring . This ring is covered with the ground wire. Electrical tapes are used for remote wire connections. These remote wires are finally connected to the receiver’s output. The speaker wires are then made to connect with the positive and negative terminals of the amplifiers and speakers.

The fuse is removed from the fuse holder. The end of the power wire is connected to the positive terminal. The positive terminal is attached to the battery post. Negative terminal is attached to the negative post. Fuse is inserted into the fuse holder.

Thus, this article explains How to Install an Amp Kit without much difficulty.

Looking to find the best deal on Auto Hifi, then visit www.powernetshop.at to find the best advice on Car audio for you.

The two main factors affecting the performance of a audio system are volume and the quality of sound that it produces. In a car stereo system, the perfect quality can be achieved only when the stereo system is connected to the amplifier. The most common thought among people is that amplifiers increase the sound alone but they also increase the overall quality of the sound coming from the stereo system. But how to connect an original car stereo to an amp?

There are few tools which are found useful in connecting an original car stereo to an amp. It includes speaker wire, rubber grommets, wiring harness adapter, amplifier wiring kit, drill, Philips head screw driver, trim panel tool, rubber spacers.

A few tools are required to complete the job these make the job easy and faster. It includes speaker wire, rubber grommets, wiring harness adapter, amplifier wiring kit, drill, Philips head screw driver, trim panel tool, rubber spacers.

The first step is to disconnect the wire connected to the negative terminal of the battery. This wire establishes a connection between the battery and the car’s frame. The next thing to do is to remove the clamp and keep it away. This can be done with the help of a Philips head screw drive.

The amplifier is mounted on the trunk of the car. In the case of trucks the amplifier is mounted below the seat to provide ventilation. The vehicle’s stereo is removed. The removal procedure varies from one vehicle to other. The manual which is issued along with the vehicle by the manufacturer is to be referred often. The stereo unit is pulled to the dash till the wiring in the rear.

The cables are drawn to the amplifier location. The panel protecting the carpeting is removed using a panel tool. Now the cables are placed below the carpeting and our hands are used in the place of the panels. The cables used for power supply are drawn starting from the battery up to the amplifier. Then the cables and the leads are connected to amplifier.

The stereo system of the car is removed. The process of removing it varies from one car to another and so it is better to go through the user’s manual before doing this job. Take out the stereo so that the wires in the back side of the stereo can be accessed easily. Now the wires attached to the stereo system are removed. Then the wires are connected to a adapter. This connection is easy to make because all the wires are colour coded.

Technology has made things easy and simple though it is complicated in its own working. The above article would have taught you how to connect an original car stereo to an amp. These works must be done with caution and accuracy. Thus take time to do this simple work with care.

Learn more about Auto. Stop by Author Name’s site where you can find out all about Car stereo and what it can do for you.